what is Fixed Prosthodontics ?
Fixed prosthodontics is concerned with restoring teeth using restorations that are fixed into the patient’s mouth. They are typically made in a laboratory after taking impressions (moulds) for the technician to work with. They are also known as ‘indirect restorations’.
Indirect restorations can be used to restore and repair single or multiple teeth, and can be used to restore relatively small spaces between the teeth. Indirect restorations are relatively strong compared to fillings that can be placed at the chair side. Often the indirect restorations can be made to look better (superior aesthetics). It is difficult to say how long fixed restorations should last. If they are planned, executed and maintained correctly, they could last anywhere up to 10-12 years, and perhaps longer. The main types of indirect restoration are shown below:
Crowns are often referred to as ‘caps’. They cover the remaining parts of the natural tooth when a large amount of structure has been lost. As such, they provide what is known as ‘full coverage’. Crowns can be constructed from many different materials, ranging from an all-metal gold crown, through to a high strength ceramic crown. The type of crown depends on the amount of tooth left, the tooth type and the patient preference.
Bridges are made to restore gaps between natural teeth. They can be held in place by a crowned adjacent tooth, or they can be stuck onto the adjacent tooth by a metal wing, with a special adhesive. Sometimes bridges are held in place on either side of the gap (conventional), sometimes on just one side (cantilever); it depends on the size of the gap and how the teeth function. Bridges can look very good, but sometimes the bridges that are stuck on with a metal wing darken the adjacent tooth a little. They are, however, much more conservative of tooth structure than if the adjacent tooth is crowned in order to hold the bridge.
A more conservative option for a crown is the inlay. It is possible to provide an inlay if a relatively small amount of tooth tissue is missing within the confines of the tooth cusps. The inlay can be made from metals, resins or ceramics.
An onlay is similar to an inlay, but it often covers over the cusps of a tooth. They are particularly useful if the tooth needs to be strengthened or reinforced. They can also be used to make the tooth longer/higher, which is useful if a worn dentition is being built back up again.
Veneers are a relatively thin piece of ceramic or resin that is glued onto the surface of a tooth. They can be used to restore damaged teeth, rotated teeth, or to improve aesthetics. Usually an amount of tooth preparation is required for the veneer to ‘sit into’ but modern techniques allow veneers to be made that stick straight onto the tooth surface, rather like fake fingernails!
And know you can know more about Fixed Prosthodontics with our new course :
with Dr Dr. Mostafa Nour, BDS,MDSc,DDSc.
Lecturer of Prosthodontics-Faculty of Dentistry- Ain Shams & MUST university
ALL ABOUT FIXED PROSTHODONTICS”Brought to you by AHC Five-day course including all there is to know about fixed prosthodontics, Hands-On workshops
Day 1 :
-Principles of Diagnosis and Treatment Plan For Fixed Prosthodontics
-Tooth Preparations, Principles and Guidelines.
-Steps of Preparation for Metal-Ceramic Restorations.
(Materials & Different Techniques).
-Impression ( Materials & Techniques).
Day 2 :
- All Ceramic Restorations.
- The drawbacks of porcelain
- Strengthening of all ceramic materials
- The recent ceramic materials
- Pressable ceramics
- Machinable ceramics
- CAD/CAM technology
- Inlays & Onlays
- Adhesion to ceramics
- Preparation of all Ceramic restorations.
- Preparation of Inlays and Onlays.
Day 3 :
Management of Endodontically Treated Teeth.(Post & Core and EndoCrown).
- Introduction to Endodontics and its Effect on Tooth structure
- Case Selection and Treatment Planning with Emphasis on Radiographic Examination
- Principles of Preparation/Modification of Endodontic tooth for post
- Types of post and core systems
- Selection of Post system and Core material
- Indirect technique: Direct Pattern and post impressions
- Selection of Cement for Different Post Systems with Cementation Procedure
- Core Build Procedure
- Failures and Their Management
hands – on
- Post space preparation
- Try-in of post and core application
- Preparation Of Endocrown
Day 4 :
- Different Bridge Designs( simple and complex cases)
- Bridge Preparation.
- common path of insertion. -different lab fabrication techniques( casting -pressing & CAD/CAM)
- Bridge Preparation.
- common path of insertion
Day 5 :
Retraction Protocols. ( classic vs advanced)
( Different Types of Impression materials used in FPD -various Impression Techniques).
- Temporization. ( materials &techniques)
- Bite Registration ( materials&techniques)
- Surface Treatment and Cementation.
- Occlusal Adjustment.
- Retraction Protocols.
- Bite Registration.